Integrated SK6812 Digital White Pixel LED

1.Intelligent reverse connect protection, the power supply reverse connection does not damage the IC.

2. Built-in signal reshaping circuit, after wave reshaping to the next driver, ensure wave-form distortion not accumulate.

3. Cascading port transmission signal by single data line.

4. 3000K / 4500K / 6500K White CCT

5. Send data at speeds of 800Kbps, scan frequency not less than 400Hz/s

6. Widely to make addressable neopixel white led strips, neopixel white matrixs that used in entertainment, stage, live performance,etc

7. Support Arduino, Glediator, SD card controller, DMX,Artnet, MADRIX NEBULA,etc

Color

Single Color

Pixel

Addressable

Protocal

SPI

Voltage

5V

More Details.

1. SK6812 white is a intelligent control LED light source that the control circuit and white chip are integrated in a package of 5050 components. Allows you to control the white color and brightness independently.

2. In contrast to the APA102c white LED which use a standard SPI interface for control (with separate data and clock signals) and has no specific timing requirements, the ws2812b white LED use a specialized one-wire ( data) control interface and require strict timing.

3. SK6812 white LED diffuse the 3 white chips inside together for a very bright but consistant light, compared to what you get by trying to mix RGB to make white (which never quite looks right).

4. Each sk6812 white LED acts like a shift register, reading incoming color data on the input pins, and then shifting the previous color data out on the output pin.

5. After transmission for each white pixel,the signal to reduce 24bit. pixel adopt auto resha -ping transmit technology, making the pixel cascade number is not limited the signal transmission, only depend on the speed of signal transmission.

6. WS2812b white LED with low driving voltage, environmental protection and energy saving, high brightness, scattering angl e is large, good consistency, low power, long life and other advantages.

7. The control chip integrated in LED above becoming more simple circuit, small volume, convenient installation.

Related Products.

2048 pixels T-1000S RGB pixel led tapes controller

2048 pixels T-1000S RGB pixel led tapes controller

Leave review

1. SD card offline controller

2. Single-port output 2048 pixels

3. DC5V-24V working

4. Support 256MB sd card

5. Lededit software

6. Control led pixel stripe tapes, led amusement lights

1. The programmable T1000s sd card led controller 2048 pixels makes controlling your LED displays easy. Compatible with wide range of addressable LEDs and DMX signal communication protocol.

2. Perfect addressable LED solution for people who don’t want to programme Arduino or other controllers. No programming code required.

3. Using the programmes LEDedit 2016 or Glediator lets you draw your LED patterns visually, you can specify how the LEDs are arranged, preview them, then upload to an SD card. The SD card plugs into the controller and displays your pattern. You can even upload video for your LEDs to display!

Comes with a 256MB SD card included.

Note: To copy files to SD card, you must first format to the SD card. SD card must be formatted as “FAT” format.

Compatible with wide range of addressable LED chipsets:

TM1803/TM1804/TM1809/TM1812/TM1825/TM1826/TM1829/TA9909/TA9912

UCS1903/UCS1912/UCS2903/UCS2909/UCS2912/UCS3903/UCS3912/UCS8903/UCS8904

LPD6803/LPD1886/LPD1882/LPD1889/LPD6812/LPD6813/LPD8806/LPD8809

SM16716/SM16726/SM16711/SM16703

WS2811/WS2801/WS2803/WS2812B/WS2813/ws2815/ws2818

LX1003/LX2003/LX2006

INK1003/INK1009

P9813/P9816/D705/P9823

SK6812/SK6822/SK6812mini/SK9822

APA102/APA102C/APA104/APA2020

TLS3001/TLS3008/TLS3100

Color
RGB
Protocol
SPI
Read More
2048 pixels K-1000C RGB RGBW pixel led tapes controller

2048 pixels K-1000C RGB RGBW pixel led tapes controller

Leave review

1. SD card offline controller

2. 1-port output 2048 pixels max

3. DC5V-24V working

4. Add a display based on old version

5. Add more IC chips + DMX512 chips

6. Comes with DMX512 chips write address code function

7. 2020 Lededit software

8. Support our all led digital strips, led pixel lights,etc

1. This K-1000c sd card led controller 2048 pixels is evolution of our classic T-1000s + K-1000D two controllers funtion together.

2. The controller has single port output that can support up to 512/2048 pixels lights(DMX lights can support up to 512 pixels).

3. Improve functions that support load lamp is 4 channels (RGBW) pixels, enhanced 485 TTL and 485 differential (DMX) signal output.

4. Controller support chip can lock the support IC in software, or not lock the support IC in the software, select the support IC through the controller CHIP button, more flexible and convenient.

5. Comes with a 256MB SD card included. This version support 2GB sd card that old ones couldn’t.

6. For the DMX lighting IC, the controller comes with write address function; In addition, with use of 2016 LedEdit-K V3.26 or later edition can make one key write address function setting.

7. The controller can single set use,also multiple controllers cascade, cascade optical isolation mode: interference, better stability, cascade distance between two controllers can reach up to 150 meters, need to use 0.5 square meters pure copper power cord.

8. Controller comes with the test effects were as follows: 1 red, green, blue and black jump; 2 red, green, blue and black gradient; 3 red, green, blue and goes.

9.Note: To copy files to SD card, you must first format to the SD card. SD card must be formatted as “FAT” format.

Compatible with wide range of addressable LED chipsets:

TM1803/TM1804/TM1809/TM1812/TM1825/TM1826/TM1829/TA9909/TA9912/TM1913/TM1914

UCS1903/UCS1912/UCS2903/UCS2909/UCS2912/UCS3903/UCS3912/UCS8903/UCS8904

LPD6803/LPD1886/LPD8812/LPD1889

SM16716/SM16726/SM16711/SM16703

WS2811/WS2801/WS2803/WS2812B/WS2813/ws2815/ws2818

LX1003/LX2003/LX2006

INK1003/INK1009

P9813/P9816/D705/9883/P9823

SK6812/SK6812RGBW/SK6822/SK6812mini/SK9822

APA102/APA102C/APA104/APA2020

TLS3001/TLS3008/TLS3100

DMX 500K/DMX 250K-CZF

GS8208/GS8205/GS8206/GS8512

Color
RGBRGBW
Protocol
SPIDMX512
Read More
SP108E LED WIFI Pixel Controller

SP108E LED WIFI Pixel Controller

Leave review

1. Long distance APP remote control via WIFI;

2. Support routing mode(AP) and LAN connection mode(STA);

3. Support almost every kind of one-wire or two-wire LED driver IC ;

4. Brightness adjustable, With 180 kinds of patterns and 8 kind of color adjustable patterns;

5.Creatively using from-image-to-effect method for user to DIY any effect;

6. Support setting pixel number and segments number, able to control up to 2048 pixels;

5. DC5V~24V wide range working voltage, preventing reverse connection of power supply;

6. User setting saving;

1. App control:
Both IOS version and Android OS version are available. (hardware should support WIFI)
•Requires IOS version 10.0 or later;
•Requires Android OS version 4.4 or later;
•Search”LedShop”in App Store or Google pay or scan this QR code to download and install the App

3. Functions:
•Button:
1.Click on the button: Switch working mode;
2.Long press the button: Enter automatic distribution network mode;
•Indicator Light:
1.Blue: AP(Access Point) mode;
2.Green: STA(Station) mode;
•Working Mode:
1.AP(Access Point) mode:The mobile phone can be directly connected to the controller in this mode,while the controller is equivalent to a Access Point.
Connect steps:
1).In the WIFI setting page of your phone,find and connect the controller(named like SP108E_XX, the default password is 12345678);
2).Open the LED Shop App ,then the controller will be showed on the device list;
2.STA(Station) mode:
Connect steps: 1. Automatic distribution network,This method is recommended for the router's WIFI band of 2.4GHZ:
1).Open LED Shop APP and make sure that your phone is connected to a WIFI network,long press the button in the controller until the
green indicator starts flashing. Input the WIFI password, then press the OK to confirm and wait for the configure processing finish;
2).When controller successfully enter the WIFI network, it will be showed on the device list;
2. Manual distribution network,This mode is used for the router to enable multi-frequency integration, and is compatible with the router
WIFI band of 2.4GHghz:
1).Open the APP;Select the WIFI network and enter the WIFI password you want to connect to,then click the nextz button in your APP.
2).Set the controller as Access Point mode (AP),At the same time, please connect the wireless name corresponding to the controller AP
mode in the setting interface of your mobile phone. The wireless name format is SP108E_XXX and click next;
3).Starting network distribution now,network distribution time will be long,please patiently wait for the completion of operation;After
the success of the distribution network,the indicator light of the controller turns green.Please go to the main interface of the LED
Shop APP and refresh the device list.After the device appears in the device list of the APP, click and control it.
3.Remove device:
1).Click the switch button to return the controller to AP mode and also to STA mode;
2).In the STA mode of controller, select the corresponding controller after the APP is connected and click remove device to move
the controller out of the current network. At this time, the controller enters AP mode.

Color
RGBRGBW
Protocol
SPIDMX512
Read More
Pixel LED Multi-function Digital Slave Controller

Pixel LED Multi-function Digital Slave Controller

Leave review

1. Multi-function Digital LED slave Controller

2. With 4 output ports, each port load 512 pixels,2048 pixels maximum

3. Support DMX512 protocol + SPI /TTL protocl IC chips

4. Connect main-controllers to work together

5. On-line is work with Madrix software

6. Off-line controller, program saved in SD card, 15 files maximum

7. Widely used in all DMX512 led products projects

8. There are 8 ports LED slave controller to choose

1. Multi-function Digital Controller. Two control model: Control online mainly means DMX512; Control offline mainly means normal SPI/TTL IC chips.

2. IP address settings on the main controller;

3. Controller with 2G SD card, program saved in SD card for offline playback;

4. Using Fast Ethernet, TCP / IP communication protocol, host connectivity LED controller via standard network cable;

5. Each slave controller has four output ports, a single port output control 512 pixels;

Color
RGBRGBW
Protocol
SPIDMX512
Read More