5V 32 Pixels DMX512 RGBW Addressable Pixel LED Digital Strip

1. Addressable DMX512 RGBW RGBWW 32 Pixels LED Digital Strip

2. DC5V, 10W/M

3. 12mm width White / Black FPCB

4. Warm white 3000K, neutral white 4500K, Cool white 6500K to choose

5. 3M adhensive tape on backside of non-waterproof strip

6. Support K-1000C/ K-8000C/ YM-501 /DMX512,Artnet to control

7.Standard DMX512 Signal wire digital control interface A,B

8. Widely used in entertainment, stage, live performance, Disco Club and TV Show, etc

Color

RGBW

Pixel

Addressable

Protocol

DMX512

Voltage

5V

More Details.

1. This strip is Addressable DMX 512 RGBW led digital strips that different with normal SPI led pixel strips.

DMX512 led strips protocl is DMX512 that signal is parallel not series.

2. Its advantage is parallel DMX512 signal could avoid RGBW LEDs color influenced by the failure of one light in serial connection.

3. Entire strip has 32 pixels ( 128 channels), 32 pcs RGBW leds in a meter with 12mm width pcb board.

4. Communication between DMX512 led digital strips are synchronized perfectly under support of Artnet / DMX512 led controllers.

5. DMX512 RGBW led pixel tape strips DMX address need to be set via DMX address coder / controller.

6. Vivid lighting performance operated by Madrix software, Artnet / DMX512 led controllers.

7. Addressable 5V DMX512 RGBW led strip is flexible , bright, durable and easy for installation.

For bare board strip, you can use the 3M adhensive tape on back; For waterproof silicone tube strip, there shipped with flexible silicon brackets and screws, the brackets fit over the waterproof sheath, it would be used to mount the led strips very well.

8. Widely used in entertainment, stage, live performance, Disco Club and TV Show, etc.

Related Products.

SP901E Pixel LED Digital TTL SPI Signal Amplifier

SP901E Pixel LED Digital TTL SPI Signal Amplifier

Leave review
Color
RGBRGBW
Protocol
SPIDMX512

1. SPI / DMX512 TTL SPI signal Amplifier

2. Support almost every kind of one-wire or two-wires LED driver IC

3. Support setting pixel number and segment numbers based on the Main controller

4. DC5V~24V wide range working voltage, reverse power supply input protection

5.This Signal Amplifier control model is depends on the main controller

6.It can work with K-1000C, SP108E, SP107E, CSY08, CSY07, Raspberry pi, Arduino X2 music controller,etc

1. This SPI / DMX512 signal amplifier is compatible with all kinds of 5V-TTL signal dual signals. It receives one signal and simultaneously output 4 or 8 channels of signals. Each channel can control the same quantity of LED pixels as main controller.

2. It can output 8 channels for addressable LED strip with single data wire, such as WS2812B, WS2811, SK6812RGB, SK6812-RGBW,UCS2904, etc. It can output 4 channels for addressable LED strip with data & clock wires WS2801, APA102, SK9822 or dual data wires, such as GS8208, WS2815.

3. DC5V~24V wide range of working voltage, but it cannot regulate the output voltage. That means the output voltage of power supply must be the same as the work voltage of your LED lights. The current through the amplifier is limited, when the current consumed is high, you need to add the power supply of the corresponding voltage.

4. Multiple signal amplifiers can be cascaded together synchronously. Particularly suitable for small and medium dream color lighting projects. It can work with K-1000C, SP108E, SP107E, CSY08, CSY07, Raspberry pi, Arduino X2 music controller,etc.

5. This Signal Amplifier control the IC chip version like SK6812 or DMX512  , pixels qty, RGB color sequence, program modles are all based on the Main controller. 

6. The controller cannot regulate the output voltage at the VCC. That means the output voltage of your power supply must be the same as the work voltage of your LED lights. If your lights need 5V input, please use a 5V power supply, don't use higher than 5V power supply

7. The current through the amplifier is limited, when the consumption current is higher, you need to add power supply of the corresponding voltage additionally.

 

Read More
DMX512/1990 convert PWM decoder

DMX512/1990 convert PWM decoder

Leave review

1. Supply voltage: 12V-24VDC

2. Output: 3 channels / 4 channels

3. Support RGB / RGBW LED

4. Static power consumption:

5. Output current: each channel 4A

6.Output power: 12V:

7. 3pin XLR Socket,RJ45 interface

1. DMX common controller adopts the advanced micro control unit, it receives standard DMX-512 digital control signal and transformed it into PWM signal for driving LED;

2. You could connect DMX module with DMX digital console to achieve dimming or various changes in procedures.

3. Each DMX common controller occupied 3 / 4 DMX addresses, adopt coding switch set address, it is a Binary numerical code switch which is setting DMX original address code from 1 to 9, 1 is the lowest, and 9 is the highest, 511 address codes could be setted in all.

4. DMX original address code equal aggregate value of the coding switch value from 1 to 9, dial the coding switch upwards (ON is setted 1), the value of bit can be gotten, on the contrary, the value of bit is 0.

5. DMX signal can be received when coding switch FUN(10)-OFF(ON is setted 0).

Color
Single ColorRGBRGBW
Protocol
PWMDMX512
Read More
DMX512 RGB RGBW LED strips address mark writer

DMX512 RGB RGBW LED strips address mark writer

Leave review

1. This DMX address writer mainly for the DMX512 IC chip we produce

2. It support standard DMX512 protocol A, B ; signle DMX512 protocol A

3. After DMX address mark ready, program inside can test the address mark if correct

4. UCS512 A,B chip need to connect the PI cable to the DMX address coder

5. UCS512 C3/C4 chip no need to connect the PI cable to the DMX address coder

1. This is a DMX address code writer mainly for the DMX512 IC chip we produce like standard DMX512 A,B or single DMX512 protocol A strips.

2. Different DMX512 IC chip lighting different colors after DMX address write ready.

3. UCS512 A,B chip led strips lighting blue color when finish to write DMX address.

4. UCS512 C3/C4 chip led strip lighting white color when the DMX address write finished.

5. We have a video to show you how to write the DMX address based on different DMX512 IC chip you choose.

Color
RGBRGBW
Protocol
DMX512
Read More
YM-501 Pixel LED Multi-function Digital Controller

YM-501 Pixel LED Multi-function Digital Controller

Leave review

1. Multi-function Digital Controller

2. With 4 output ports, each port load 512 pixels,2048 pixels maximum

3. Support DMX512 protocol + SPI /TTL protocl IC chips

4. Connect sub-controllers when product is DMX512 chips that on-line

5. On-line is work with Madrix software

6. Click buttons or remoter to control program models, speed

7. Off-line controller, program saved in SD card, 15 files maximum

8. Widely used in all DMX512 led products projects

1. Multi-function Digital Controller. Two control model: Control online mainly means DMX512; Control offline mainly means normal SPI/TTL IC chips.

2. IP address settings: with LCD display, no DIP switch design, all IP and MAC is set to be completed by the key;

3. Controller with 2G SD card, program saved in SD card for offline playback;

4. Using Fast Ethernet, TCP / IP communication protocol, host connectivity LED controller via standard network cable;

5. Each controller has four output ports, a single port output control 512 pixels;

6. This multip function LED cotroller have master controller function too, that on-line can be cascaded to 16 sub-controllers, 31 units can be cascaded off of control maximum;

7 Grayscale settings: Customers can never light gray under the circumstances to 65,536 (64K) adjust the gray, LED lights let you achieve the best display effect;

8. Brightness adjustment: 100 automatic brightness adjustment function allows you to adjust the display brightness is more effective;

9. EMC design, with good anti-jamming capability;

Color
RGBRGBW
Protocol
SPIDMX512
Read More