5V Addressable 30Leds 5-in-1 RGBTW RGBWW pixel led tape

1. Addressable 5-in-1 RGBTW RGBWW Pixel LED Digital Strip

2. DC5V, 12W/M

3. 12mm width White / Black FPCB

4. Warm white 2700K,Cool white 6500K to choose

5. 30pcs 5-in-1 RGBWW RGBTW LEDs plus 30 pcs LPD8806 IC chip

6. 3M adhensive tape on backside of non-waterproof strip

7. Support K-1000C/ K-8000C/ YM-501 /DMX512,Artnet /MADRIX NEBULA to control

8. Widely used in entertainment, stage, live performance, Disco Club and TV Show, etc

Color

RGBW

Pixel

Addressable

Protocol

SPI

Voltage

5V

More Details.

1. This high addressable 5 colors RGBWW 30 pixel tapes are incredibly cool that each led is powered by a LPD8806 IC chip that enables them to be individually addressable.

2. Compared to the integrated SK6812 RGBW ones, this external IC chip LPD8806 5-in-1 RGBW LED strip has much higher brightness and much colors available which colors range from warm white 2700K to 6500K.

3. Entire strip has 30 pixels ( 150channels), 30 pcs RGBWW leds in a meter with 12mm width pcb board.

4. There are Warm white 2700K, Cold white 6500K white CCT to choose.Of course, if you need other colors, we are offer to customized.

5. The strip is made of flexible PCB material, you can cut this stuff pretty easily with wire cutters, there are cut-lines every LED. Solder to the 0.1" copper pads and you're good to go.

6. If the strip does get damaged, it is often one led copper unit broken, in such case, cutting of this copper unit segment and resoldering the rest copper units together brings the strip back to life.

7. Vivid lighting performance operated by Arduino, Raspberry Pi , Madrix software, Artnet / DMX512 /MADRIX NEBULA.

Related Products.

DMX512/1990 convert PWM decoder

DMX512/1990 convert PWM decoder

Leave review

1. Supply voltage: 12V-24VDC

2. Output: 3 channels / 4 channels

3. Support RGB / RGBW LED

4. Static power consumption:

5. Output current: each channel 4A

6.Output power: 12V:

7. 3pin XLR Socket,RJ45 interface

1. DMX common controller adopts the advanced micro control unit, it receives standard DMX-512 digital control signal and transformed it into PWM signal for driving LED;

2. You could connect DMX module with DMX digital console to achieve dimming or various changes in procedures.

3. Each DMX common controller occupied 3 / 4 DMX addresses, adopt coding switch set address, it is a Binary numerical code switch which is setting DMX original address code from 1 to 9, 1 is the lowest, and 9 is the highest, 511 address codes could be setted in all.

4. DMX original address code equal aggregate value of the coding switch value from 1 to 9, dial the coding switch upwards (ON is setted 1), the value of bit can be gotten, on the contrary, the value of bit is 0.

5. DMX signal can be received when coding switch FUN(10)-OFF(ON is setted 0).

Color
Single ColorRGBRGBW
Protocol
PWMDMX512
Read More
SP108E LED WIFI Pixel Controller

SP108E LED WIFI Pixel Controller

Leave review

1. Long distance APP remote control via WIFI;

2. Support routing mode(AP) and LAN connection mode(STA);

3. Support almost every kind of one-wire or two-wire LED driver IC ;

4. Brightness adjustable, With 180 kinds of patterns and 8 kind of color adjustable patterns;

5.Creatively using from-image-to-effect method for user to DIY any effect;

6. Support setting pixel number and segments number, able to control up to 2048 pixels;

5. DC5V~24V wide range working voltage, preventing reverse connection of power supply;

6. User setting saving;

1. App control:
Both IOS version and Android OS version are available. (hardware should support WIFI)
•Requires IOS version 10.0 or later;
•Requires Android OS version 4.4 or later;
•Search”LedShop”in App Store or Google pay or scan this QR code to download and install the App

3. Functions:
•Button:
1.Click on the button: Switch working mode;
2.Long press the button: Enter automatic distribution network mode;
•Indicator Light:
1.Blue: AP(Access Point) mode;
2.Green: STA(Station) mode;
•Working Mode:
1.AP(Access Point) mode:The mobile phone can be directly connected to the controller in this mode,while the controller is equivalent to a Access Point.
Connect steps:
1).In the WIFI setting page of your phone,find and connect the controller(named like SP108E_XX, the default password is 12345678);
2).Open the LED Shop App ,then the controller will be showed on the device list;
2.STA(Station) mode:
Connect steps: 1. Automatic distribution network,This method is recommended for the router's WIFI band of 2.4GHZ:
1).Open LED Shop APP and make sure that your phone is connected to a WIFI network,long press the button in the controller until the
green indicator starts flashing. Input the WIFI password, then press the OK to confirm and wait for the configure processing finish;
2).When controller successfully enter the WIFI network, it will be showed on the device list;
2. Manual distribution network,This mode is used for the router to enable multi-frequency integration, and is compatible with the router
WIFI band of 2.4GHghz:
1).Open the APP;Select the WIFI network and enter the WIFI password you want to connect to,then click the nextz button in your APP.
2).Set the controller as Access Point mode (AP),At the same time, please connect the wireless name corresponding to the controller AP
mode in the setting interface of your mobile phone. The wireless name format is SP108E_XXX and click next;
3).Starting network distribution now,network distribution time will be long,please patiently wait for the completion of operation;After
the success of the distribution network,the indicator light of the controller turns green.Please go to the main interface of the LED
Shop APP and refresh the device list.After the device appears in the device list of the APP, click and control it.
3.Remove device:
1).Click the switch button to return the controller to AP mode and also to STA mode;
2).In the STA mode of controller, select the corresponding controller after the APP is connected and click remove device to move
the controller out of the current network. At this time, the controller enters AP mode.

Color
RGBRGBW
Protocol
SPIDMX512
Read More
2048 pixels T-1000S RGB pixel led tapes controller

2048 pixels T-1000S RGB pixel led tapes controller

Leave review

1. SD card offline controller

2. Single-port output 2048 pixels

3. DC5V-24V working

4. Support 256MB sd card

5. Lededit software

6. Control led pixel stripe tapes, led amusement lights

1. The programmable T1000s sd card led controller 2048 pixels makes controlling your LED displays easy. Compatible with wide range of addressable LEDs and DMX signal communication protocol.

2. Perfect addressable LED solution for people who don’t want to programme Arduino or other controllers. No programming code required.

3. Using the programmes LEDedit 2016 or Glediator lets you draw your LED patterns visually, you can specify how the LEDs are arranged, preview them, then upload to an SD card. The SD card plugs into the controller and displays your pattern. You can even upload video for your LEDs to display!

Comes with a 256MB SD card included.

Note: To copy files to SD card, you must first format to the SD card. SD card must be formatted as “FAT” format.

Compatible with wide range of addressable LED chipsets:

TM1803/TM1804/TM1809/TM1812/TM1825/TM1826/TM1829/TA9909/TA9912

UCS1903/UCS1912/UCS2903/UCS2909/UCS2912/UCS3903/UCS3912/UCS8903/UCS8904

LPD6803/LPD1886/LPD1882/LPD1889/LPD6812/LPD6813/LPD8806/LPD8809

SM16716/SM16726/SM16711/SM16703

WS2811/WS2801/WS2803/WS2812B/WS2813/ws2815/ws2818

LX1003/LX2003/LX2006

INK1003/INK1009

P9813/P9816/D705/P9823

SK6812/SK6822/SK6812mini/SK9822

APA102/APA102C/APA104/APA2020

TLS3001/TLS3008/TLS3100

Color
RGB
Protocol
SPI
Read More
SP107E Bluetooth LED Music Pixel Controller

SP107E Bluetooth LED Music Pixel Controller

Leave review
Color
RGBRGBW
Protocol
SPIDMX512

1. Long distance APP remote control via Blutooth

2. Support almost every kind of one-wire or two-wires LED driver IC

3. Support setting pixel number and segment number, support up to 960 pixels

4. With 18 kinds of LED strip music effects, 30 kinds of LED matrix music effects and 180 kinds of non-music effects

5. DC5V~24V wide range working voltage, reverse power supply input protection

6. User setting saving

1. Download and install the APP:
Both IOS version and Android OS version are available. (hardware should support Bluetooth)
•Requires IOS version 10.0 or later;
•Requires Android OS version 4.4 or later;
•Search “LED Chord” in App Store or Google Play or scan this QR code to download and install the APP;

2. Instructions:
APP Operatings:
1.Make sure you have turn on Bluetooth on your phone;
2.Open the APP, drag to refresh the device list, select device name “SP107E” to connect the controller, once connected you will able to rename your
controller;
3.Select RGB order and IC type;
4.Adjust pixel number;
5.Press ENTER.
Audio Input:
There are two ways to input the audio signal on SP107E, AUX IN and Build-IN microphone;
•AUX IN: Plug the supplied audio split cable into the “AUX IN” jack, connect the audio output source(MP3,Phone or tablet…)and the speaker(or
headset), controller will automatically switch into AUX input mode;
•MIC: Disconnect the audio cable, controller will automatically switch into microphone input mode.

Read More