Addressable Digital RGB COB LED Pixel Strip

1. Addressable Digital RGB COB LED Pixel Strip

2. DC5V , 332 LEDs/m

3. 12W/m, CRI>80

4. 10mm width FPCB

5. WS2811/WS2812b/SK6812 RGB protocol compitable

6. 3M adhensive tape on backside of non-waterproof strip

7. Support K-1000C/ K-8000C/ YM-501 /DMX512 control/MADRIX NEBULA,Artnet

Color

RGB

Pixel

Addressable

Protocol

SPI

Voltage

5V

More Details.

1. Amazing, this is Addressable Digital RGB COB LED Pixel Strip. Not the single color COB led strip. 

2. The COB led strips biggest advantage is no glare, beautiful appearance,soft luminous surface, without spot that compared to the classical addressable rgb pixel led strips like ws2812b,sk6812 led strips

3. The LEDs are controlled by shift-registers that are chained up and down the tape so you can shorten or lengthen the tape.

4. SK6812 RGB LED chip is soldering on the PCB directly, on the top, glue the silicone.

5. The strip is made of flexible PCB material, you can cut this stuff pretty easily with wire cutters on the back side of PCB, there are cut-lines .Solder to the 0.1" copper pads and you're good to go.

6. If the strip does get damaged, it is often one led copper unit broken, in such case, cutting of this copper unit segment and resoldering the rest copper units together brings the strip back to life.

7. For the addressable digital RGB COB led pixel tape, we only have 332 leds/m currently

8. Vivid lighting performance operated by Arduino, Raspberry Pi, Madrix,Artnet/DMX/MADRIX NEBULA.

9. The COB LED strips, consider the high density leds, we do not recommend to choose the IP67 or IP68. 

Related Products.

DMX512/1990 convert PWM decoder

DMX512/1990 convert PWM decoder

Leave review

1. Supply voltage: 12V-24VDC

2. Output: 3 channels / 4 channels

3. Support RGB / RGBW LED

4. Static power consumption:

5. Output current: each channel 4A

6.Output power: 12V:

7. 3pin XLR Socket,RJ45 interface

1. DMX common controller adopts the advanced micro control unit, it receives standard DMX-512 digital control signal and transformed it into PWM signal for driving LED;

2. You could connect DMX module with DMX digital console to achieve dimming or various changes in procedures.

3. Each DMX common controller occupied 3 / 4 DMX addresses, adopt coding switch set address, it is a Binary numerical code switch which is setting DMX original address code from 1 to 9, 1 is the lowest, and 9 is the highest, 511 address codes could be setted in all.

4. DMX original address code equal aggregate value of the coding switch value from 1 to 9, dial the coding switch upwards (ON is setted 1), the value of bit can be gotten, on the contrary, the value of bit is 0.

5. DMX signal can be received when coding switch FUN(10)-OFF(ON is setted 0).

Color
Single ColorRGBRGBW
Protocol
PWMDMX512
Read More
8192 pixels K-8000C RGB RGBW Pixel led tapes controller

8192 pixels K-8000C RGB RGBW Pixel led tapes controller

Leave review

1. SD card offline controller

2. 8-port output 8192 pixels maximum

3. DC5V-24V working

4. Add a display based on old version

5. Add more IC chips + DMX512 chips

6. Comes with DMX512 chips write address code function

7. Support our all led digital strips, led pixel lights,etc

1、K-8000C is evolution of K-8000D + T-8000A two functions together.

2、Controller has eight ports output, each port can support up to 512/1024 lights(DMX lights can support up to 512 pixels).

3、Program saved in SD card, the SD card can store up to 32 files, SD cared capacity supports 128MB-32GB.

4、The controller can single set use,also multiple controllers cascade, cascade optical isolation mode: interference, better stability, cascade distance between two controllers can reach up to 150 meters, need to use 0.5 square meters pure copper power cord.

5、Controller support chip can lock the support IC in software, or not lock the support IC in the software, select the support IC through the controller CHIP button, this scheme is more flexible and convenient.

6、For the DMX lighting IC, the controller comes with write address function; In addition, with use of our 2020 LedEdit-K V3.26 or later edition can make one key write address function setting.

7、Support load lamp is 4 channels (RGBW) pixels, or split into single channel point pixels.

8、Enhanced 485 TTL and 485 differential (DMX) signal output.

9、The controller comes with the test effects were as follows: 1 red, green, blue and black jump; 2 red, green, blue and black gradient; 3 red, green, blue and goes.

Compatible with wide range of addressable LED chipsets:

TM1803/TM1804/TM1809/TM1812/TM1825/TM1826/TM1829/TA9909/TA9912/TM1913/TM1914

UCS1903/UCS1912/UCS2903/UCS2909/UCS2912/UCS3903/UCS3912/UCS8903/UCS8904

LPD6803/LPD1886/LPD1882/LPD1889

SM16716/SM16726/SM16711/SM16703

WS2811/WS2801/WS2803/WS2812B/WS2813/ws2815/ws2818

LX1003/LX2003/LX2006

INK1003/INK1009

P9813/P9816/D705/9883/P9823

SK6812/SK6812RGBW/SK6822/SK6812mini/SK9822

APA102/APA102C/APA104/APA2020

TLS3001/TLS3008/TLS3100

DMX 500K/DMX 250K-CZF

GS8208/GS8205/GS8206/GS8512

Color
RGBRGBW
Protocol
SPIDMX512
Read More
2048 pixels K-1000C RGB RGBW pixel led tapes controller

2048 pixels K-1000C RGB RGBW pixel led tapes controller

Leave review

1. SD card offline controller

2. 1-port output 2048 pixels max

3. DC5V-24V working

4. Add a display based on old version

5. Add more IC chips + DMX512 chips

6. Comes with DMX512 chips write address code function

7. 2020 Lededit software

8. Support our all led digital strips, led pixel lights,etc

1. This K-1000c sd card led controller 2048 pixels is evolution of our classic T-1000s + K-1000D two controllers funtion together.

2. The controller has single port output that can support up to 512/2048 pixels lights(DMX lights can support up to 512 pixels).

3. Improve functions that support load lamp is 4 channels (RGBW) pixels, enhanced 485 TTL and 485 differential (DMX) signal output.

4. Controller support chip can lock the support IC in software, or not lock the support IC in the software, select the support IC through the controller CHIP button, more flexible and convenient.

5. Comes with a 256MB SD card included. This version support 2GB sd card that old ones couldn’t.

6. For the DMX lighting IC, the controller comes with write address function; In addition, with use of 2016 LedEdit-K V3.26 or later edition can make one key write address function setting.

7. The controller can single set use,also multiple controllers cascade, cascade optical isolation mode: interference, better stability, cascade distance between two controllers can reach up to 150 meters, need to use 0.5 square meters pure copper power cord.

8. Controller comes with the test effects were as follows: 1 red, green, blue and black jump; 2 red, green, blue and black gradient; 3 red, green, blue and goes.

9.Note: To copy files to SD card, you must first format to the SD card. SD card must be formatted as “FAT” format.

Compatible with wide range of addressable LED chipsets:

TM1803/TM1804/TM1809/TM1812/TM1825/TM1826/TM1829/TA9909/TA9912/TM1913/TM1914

UCS1903/UCS1912/UCS2903/UCS2909/UCS2912/UCS3903/UCS3912/UCS8903/UCS8904

LPD6803/LPD1886/LPD8812/LPD1889

SM16716/SM16726/SM16711/SM16703

WS2811/WS2801/WS2803/WS2812B/WS2813/ws2815/ws2818

LX1003/LX2003/LX2006

INK1003/INK1009

P9813/P9816/D705/9883/P9823

SK6812/SK6812RGBW/SK6822/SK6812mini/SK9822

APA102/APA102C/APA104/APA2020

TLS3001/TLS3008/TLS3100

DMX 500K/DMX 250K-CZF

GS8208/GS8205/GS8206/GS8512

Color
RGBRGBW
Protocol
SPIDMX512
Read More
SP108E LED WIFI Pixel Controller

SP108E LED WIFI Pixel Controller

Leave review

1. Long distance APP remote control via WIFI;

2. Support routing mode(AP) and LAN connection mode(STA);

3. Support almost every kind of one-wire or two-wire LED driver IC ;

4. Brightness adjustable, With 180 kinds of patterns and 8 kind of color adjustable patterns;

5.Creatively using from-image-to-effect method for user to DIY any effect;

6. Support setting pixel number and segments number, able to control up to 2048 pixels;

5. DC5V~24V wide range working voltage, preventing reverse connection of power supply;

6. User setting saving;

1. App control:
Both IOS version and Android OS version are available. (hardware should support WIFI)
•Requires IOS version 10.0 or later;
•Requires Android OS version 4.4 or later;
•Search”LedShop”in App Store or Google pay or scan this QR code to download and install the App

3. Functions:
•Button:
1.Click on the button: Switch working mode;
2.Long press the button: Enter automatic distribution network mode;
•Indicator Light:
1.Blue: AP(Access Point) mode;
2.Green: STA(Station) mode;
•Working Mode:
1.AP(Access Point) mode:The mobile phone can be directly connected to the controller in this mode,while the controller is equivalent to a Access Point.
Connect steps:
1).In the WIFI setting page of your phone,find and connect the controller(named like SP108E_XX, the default password is 12345678);
2).Open the LED Shop App ,then the controller will be showed on the device list;
2.STA(Station) mode:
Connect steps: 1. Automatic distribution network,This method is recommended for the router's WIFI band of 2.4GHZ:
1).Open LED Shop APP and make sure that your phone is connected to a WIFI network,long press the button in the controller until the
green indicator starts flashing. Input the WIFI password, then press the OK to confirm and wait for the configure processing finish;
2).When controller successfully enter the WIFI network, it will be showed on the device list;
2. Manual distribution network,This mode is used for the router to enable multi-frequency integration, and is compatible with the router
WIFI band of 2.4GHghz:
1).Open the APP;Select the WIFI network and enter the WIFI password you want to connect to,then click the nextz button in your APP.
2).Set the controller as Access Point mode (AP),At the same time, please connect the wireless name corresponding to the controller AP
mode in the setting interface of your mobile phone. The wireless name format is SP108E_XXX and click next;
3).Starting network distribution now,network distribution time will be long,please patiently wait for the completion of operation;After
the success of the distribution network,the indicator light of the controller turns green.Please go to the main interface of the LED
Shop APP and refresh the device list.After the device appears in the device list of the APP, click and control it.
3.Remove device:
1).Click the switch button to return the controller to AP mode and also to STA mode;
2).In the STA mode of controller, select the corresponding controller after the APP is connected and click remove device to move
the controller out of the current network. At this time, the controller enters AP mode.

Color
RGBRGBW
Protocol
SPIDMX512
Read More