5V Addressable 60 LEDs WWA White Pixel Led strip

1. Addressable 60 LEDs SK6812 WWA White Pixel Led strip

2. DC5V, 14W/M

3. 10mm width White /Black FPCB

4. 2pin / 3pin JST-SM connector

5. 3M adhesive tape on backside of non-waterproof tape

6. Support K-1000C/ K-8000C/ YM-501 /DMX512 control/MADRIX NEBULA,Artnet

7. Amber ( 1800-2000K ) -- Warm White ( 2700 - 3000K ) -- White ( 6000 -7000K )

Color

RGB

Pixel

Addressable

Protocol

SPI

Voltage

5V

More Details.

1. These addressable SK6812 WWA white pixel tape are incredibly cool that each led is powered by a sk6812 that enables them to be individually addressable.

2. What an amazing is there are 3 version white CCT can play in one LED strip, especially they are digital white pixel led strip instead of analog white led strips.

3. SK6812 WWA LED is single digital out pin ,the PWM is built into each LED-chip so once you set the color you can stop talking to the strip and it will continue to PWM all the LEDs.

4. The strip is made of flexible PCB material, you can cut this stuff pretty easily with wire cutters, there are cut-lines every LED. Solder to the 0.1" copper pads and you're good to go.

5. There not only have 60 pixels SK6812 WWA digital led tapes to choose, but also have 30-144 pixels SK6812 WWA digital white pixel led strips and UCS2909 addressable triple white led tape.

6. Compared to the UCS2909 3-in-1 White pixel LED strip, SK6812 WWA led strip brightness is a little dimmer. 

7. Vivid lighting performance operated by Arduino, Raspberry Pi , Madrix software, Artnet / DMX512 /MADRIX NEBULA.

Related Products.

Pixel LED Multi-function Digital Slave Controller

Pixel LED Multi-function Digital Slave Controller

Leave review

1. Multi-function Digital LED slave Controller

2. With 4 output ports, each port load 512 pixels,2048 pixels maximum

3. Support DMX512 protocol + SPI /TTL protocl IC chips

4. Connect main-controllers to work together

5. On-line is work with Madrix software

6. Off-line controller, program saved in SD card, 15 files maximum

7. Widely used in all DMX512 led products projects

8. There are 8 ports LED slave controller to choose

1. Multi-function Digital Controller. Two control model: Control online mainly means DMX512; Control offline mainly means normal SPI/TTL IC chips.

2. IP address settings on the main controller;

3. Controller with 2G SD card, program saved in SD card for offline playback;

4. Using Fast Ethernet, TCP / IP communication protocol, host connectivity LED controller via standard network cable;

5. Each slave controller has four output ports, a single port output control 512 pixels;

Color
RGBRGBW
Protocol
SPIDMX512
Read More
SP901E Pixel LED Digital TTL SPI Signal Amplifier

SP901E Pixel LED Digital TTL SPI Signal Amplifier

Leave review
Color
RGBRGBW
Protocol
SPIDMX512

1. SPI / DMX512 TTL SPI signal Amplifier

2. Support almost every kind of one-wire or two-wires LED driver IC

3. Support setting pixel number and segment numbers based on the Main controller

4. DC5V~24V wide range working voltage, reverse power supply input protection

5.This Signal Amplifier control model is depends on the main controller

6.It can work with K-1000C, SP108E, SP107E, CSY08, CSY07, Raspberry pi, Arduino X2 music controller,etc

1. This SPI / DMX512 signal amplifier is compatible with all kinds of 5V-TTL signal dual signals. It receives one signal and simultaneously output 4 or 8 channels of signals. Each channel can control the same quantity of LED pixels as main controller.

2. It can output 8 channels for addressable LED strip with single data wire, such as WS2812B, WS2811, SK6812RGB, SK6812-RGBW,UCS2904, etc. It can output 4 channels for addressable LED strip with data & clock wires WS2801, APA102, SK9822 or dual data wires, such as GS8208, WS2815.

3. DC5V~24V wide range of working voltage, but it cannot regulate the output voltage. That means the output voltage of power supply must be the same as the work voltage of your LED lights. The current through the amplifier is limited, when the current consumed is high, you need to add the power supply of the corresponding voltage.

4. Multiple signal amplifiers can be cascaded together synchronously. Particularly suitable for small and medium dream color lighting projects. It can work with K-1000C, SP108E, SP107E, CSY08, CSY07, Raspberry pi, Arduino X2 music controller,etc.

5. This Signal Amplifier control the IC chip version like SK6812 or DMX512  , pixels qty, RGB color sequence, program modles are all based on the Main controller. 

6. The controller cannot regulate the output voltage at the VCC. That means the output voltage of your power supply must be the same as the work voltage of your LED lights. If your lights need 5V input, please use a 5V power supply, don't use higher than 5V power supply

7. The current through the amplifier is limited, when the consumption current is higher, you need to add power supply of the corresponding voltage additionally.

 

Read More
YM-501 Pixel LED Multi-function Digital Controller

YM-501 Pixel LED Multi-function Digital Controller

Leave review

1. Multi-function Digital Controller

2. With 4 output ports, each port load 512 pixels,2048 pixels maximum

3. Support DMX512 protocol + SPI /TTL protocl IC chips

4. Connect sub-controllers when product is DMX512 chips that on-line

5. On-line is work with Madrix software

6. Click buttons or remoter to control program models, speed

7. Off-line controller, program saved in SD card, 15 files maximum

8. Widely used in all DMX512 led products projects

1. Multi-function Digital Controller. Two control model: Control online mainly means DMX512; Control offline mainly means normal SPI/TTL IC chips.

2. IP address settings: with LCD display, no DIP switch design, all IP and MAC is set to be completed by the key;

3. Controller with 2G SD card, program saved in SD card for offline playback;

4. Using Fast Ethernet, TCP / IP communication protocol, host connectivity LED controller via standard network cable;

5. Each controller has four output ports, a single port output control 512 pixels;

6. This multip function LED cotroller have master controller function too, that on-line can be cascaded to 16 sub-controllers, 31 units can be cascaded off of control maximum;

7 Grayscale settings: Customers can never light gray under the circumstances to 65,536 (64K) adjust the gray, LED lights let you achieve the best display effect;

8. Brightness adjustment: 100 automatic brightness adjustment function allows you to adjust the display brightness is more effective;

9. EMC design, with good anti-jamming capability;

Color
RGBRGBW
Protocol
SPIDMX512
Read More
2048 pixels K-1000C RGB RGBW pixel led tapes controller

2048 pixels K-1000C RGB RGBW pixel led tapes controller

Leave review

1. SD card offline controller

2. 1-port output 2048 pixels max

3. DC5V-24V working

4. Add a display based on old version

5. Add more IC chips + DMX512 chips

6. Comes with DMX512 chips write address code function

7. 2020 Lededit software

8. Support our all led digital strips, led pixel lights,etc

1. This K-1000c sd card led controller 2048 pixels is evolution of our classic T-1000s + K-1000D two controllers funtion together.

2. The controller has single port output that can support up to 512/2048 pixels lights(DMX lights can support up to 512 pixels).

3. Improve functions that support load lamp is 4 channels (RGBW) pixels, enhanced 485 TTL and 485 differential (DMX) signal output.

4. Controller support chip can lock the support IC in software, or not lock the support IC in the software, select the support IC through the controller CHIP button, more flexible and convenient.

5. Comes with a 256MB SD card included. This version support 2GB sd card that old ones couldn’t.

6. For the DMX lighting IC, the controller comes with write address function; In addition, with use of 2016 LedEdit-K V3.26 or later edition can make one key write address function setting.

7. The controller can single set use,also multiple controllers cascade, cascade optical isolation mode: interference, better stability, cascade distance between two controllers can reach up to 150 meters, need to use 0.5 square meters pure copper power cord.

8. Controller comes with the test effects were as follows: 1 red, green, blue and black jump; 2 red, green, blue and black gradient; 3 red, green, blue and goes.

9.Note: To copy files to SD card, you must first format to the SD card. SD card must be formatted as “FAT” format.

Compatible with wide range of addressable LED chipsets:

TM1803/TM1804/TM1809/TM1812/TM1825/TM1826/TM1829/TA9909/TA9912/TM1913/TM1914

UCS1903/UCS1912/UCS2903/UCS2909/UCS2912/UCS3903/UCS3912/UCS8903/UCS8904

LPD6803/LPD1886/LPD8812/LPD1889

SM16716/SM16726/SM16711/SM16703

WS2811/WS2801/WS2803/WS2812B/WS2813/ws2815/ws2818

LX1003/LX2003/LX2006

INK1003/INK1009

P9813/P9816/D705/9883/P9823

SK6812/SK6812RGBW/SK6822/SK6812mini/SK9822

APA102/APA102C/APA104/APA2020

TLS3001/TLS3008/TLS3100

DMX 500K/DMX 250K-CZF

GS8208/GS8205/GS8206/GS8512

Color
RGBRGBW
Protocol
SPIDMX512
Read More