SP901E Pixel LED Digital TTL SPI Signal Amplifier

1. SPI / DMX512 TTL SPI signal Amplifier

2. Support almost every kind of one-wire or two-wires LED driver IC

3. Support setting pixel number and segment numbers based on the Main controller

4. DC5V~24V wide range working voltage, reverse power supply input protection

5.This Signal Amplifier control model is depends on the main controller

6.It can work with K-1000C, SP108E, SP107E, CSY08, CSY07, Raspberry pi, Arduino X2 music controller,etc

Color

RGBRGBW

Protocol

SPIDMX512

More Details.

1. This SPI / DMX512 signal amplifier is compatible with all kinds of 5V-TTL signal dual signals. It receives one signal and simultaneously output 4 or 8 channels of signals. Each channel can control the same quantity of LED pixels as main controller.

2. It can output 8 channels for addressable LED strip with single data wire, such as WS2812B, WS2811, SK6812RGB, SK6812-RGBW,UCS2904, etc. It can output 4 channels for addressable LED strip with data & clock wires WS2801, APA102, SK9822 or dual data wires, such as GS8208, WS2815.

3. DC5V~24V wide range of working voltage, but it cannot regulate the output voltage. That means the output voltage of power supply must be the same as the work voltage of your LED lights. The current through the amplifier is limited, when the current consumed is high, you need to add the power supply of the corresponding voltage.

4. Multiple signal amplifiers can be cascaded together synchronously. Particularly suitable for small and medium dream color lighting projects. It can work with K-1000C, SP108E, SP107E, CSY08, CSY07, Raspberry pi, Arduino X2 music controller,etc.

5. This Signal Amplifier control the IC chip version like SK6812 or DMX512  , pixels qty, RGB color sequence, program modles are all based on the Main controller. 

6. The controller cannot regulate the output voltage at the VCC. That means the output voltage of your power supply must be the same as the work voltage of your LED lights. If your lights need 5V input, please use a 5V power supply, don't use higher than 5V power supply

7. The current through the amplifier is limited, when the consumption current is higher, you need to add power supply of the corresponding voltage additionally.

 

Related Products.

SP901E Pixel LED Digital TTL SPI Signal Amplifier

SP901E Pixel LED Digital TTL SPI Signal Amplifier

Leave review
Color
RGBRGBW
Protocol
SPIDMX512

1. SPI / DMX512 TTL SPI signal Amplifier

2. Support almost every kind of one-wire or two-wires LED driver IC

3. Support setting pixel number and segment numbers based on the Main controller

4. DC5V~24V wide range working voltage, reverse power supply input protection

5.This Signal Amplifier control model is depends on the main controller

6.It can work with K-1000C, SP108E, SP107E, CSY08, CSY07, Raspberry pi, Arduino X2 music controller,etc

1. This SPI / DMX512 signal amplifier is compatible with all kinds of 5V-TTL signal dual signals. It receives one signal and simultaneously output 4 or 8 channels of signals. Each channel can control the same quantity of LED pixels as main controller.

2. It can output 8 channels for addressable LED strip with single data wire, such as WS2812B, WS2811, SK6812RGB, SK6812-RGBW,UCS2904, etc. It can output 4 channels for addressable LED strip with data & clock wires WS2801, APA102, SK9822 or dual data wires, such as GS8208, WS2815.

3. DC5V~24V wide range of working voltage, but it cannot regulate the output voltage. That means the output voltage of power supply must be the same as the work voltage of your LED lights. The current through the amplifier is limited, when the current consumed is high, you need to add the power supply of the corresponding voltage.

4. Multiple signal amplifiers can be cascaded together synchronously. Particularly suitable for small and medium dream color lighting projects. It can work with K-1000C, SP108E, SP107E, CSY08, CSY07, Raspberry pi, Arduino X2 music controller,etc.

5. This Signal Amplifier control the IC chip version like SK6812 or DMX512  , pixels qty, RGB color sequence, program modles are all based on the Main controller. 

6. The controller cannot regulate the output voltage at the VCC. That means the output voltage of your power supply must be the same as the work voltage of your LED lights. If your lights need 5V input, please use a 5V power supply, don't use higher than 5V power supply

7. The current through the amplifier is limited, when the consumption current is higher, you need to add power supply of the corresponding voltage additionally.

 

Read More
SP108E LED WIFI Pixel Controller

SP108E LED WIFI Pixel Controller

Leave review

1. Long distance APP remote control via WIFI;

2. Support routing mode(AP) and LAN connection mode(STA);

3. Support almost every kind of one-wire or two-wire LED driver IC ;

4. Brightness adjustable, With 180 kinds of patterns and 8 kind of color adjustable patterns;

5.Creatively using from-image-to-effect method for user to DIY any effect;

6. Support setting pixel number and segments number, able to control up to 2048 pixels;

5. DC5V~24V wide range working voltage, preventing reverse connection of power supply;

6. User setting saving;

1. App control:
Both IOS version and Android OS version are available. (hardware should support WIFI)
•Requires IOS version 10.0 or later;
•Requires Android OS version 4.4 or later;
•Search”LedShop”in App Store or Google pay or scan this QR code to download and install the App

3. Functions:
•Button:
1.Click on the button: Switch working mode;
2.Long press the button: Enter automatic distribution network mode;
•Indicator Light:
1.Blue: AP(Access Point) mode;
2.Green: STA(Station) mode;
•Working Mode:
1.AP(Access Point) mode:The mobile phone can be directly connected to the controller in this mode,while the controller is equivalent to a Access Point.
Connect steps:
1).In the WIFI setting page of your phone,find and connect the controller(named like SP108E_XX, the default password is 12345678);
2).Open the LED Shop App ,then the controller will be showed on the device list;
2.STA(Station) mode:
Connect steps: 1. Automatic distribution network,This method is recommended for the router's WIFI band of 2.4GHZ:
1).Open LED Shop APP and make sure that your phone is connected to a WIFI network,long press the button in the controller until the
green indicator starts flashing. Input the WIFI password, then press the OK to confirm and wait for the configure processing finish;
2).When controller successfully enter the WIFI network, it will be showed on the device list;
2. Manual distribution network,This mode is used for the router to enable multi-frequency integration, and is compatible with the router
WIFI band of 2.4GHghz:
1).Open the APP;Select the WIFI network and enter the WIFI password you want to connect to,then click the nextz button in your APP.
2).Set the controller as Access Point mode (AP),At the same time, please connect the wireless name corresponding to the controller AP
mode in the setting interface of your mobile phone. The wireless name format is SP108E_XXX and click next;
3).Starting network distribution now,network distribution time will be long,please patiently wait for the completion of operation;After
the success of the distribution network,the indicator light of the controller turns green.Please go to the main interface of the LED
Shop APP and refresh the device list.After the device appears in the device list of the APP, click and control it.
3.Remove device:
1).Click the switch button to return the controller to AP mode and also to STA mode;
2).In the STA mode of controller, select the corresponding controller after the APP is connected and click remove device to move
the controller out of the current network. At this time, the controller enters AP mode.

Color
RGBRGBW
Protocol
SPIDMX512
Read More
2048 pixels T-1000S RGB pixel led tapes controller

2048 pixels T-1000S RGB pixel led tapes controller

Leave review

1. SD card offline controller

2. Single-port output 2048 pixels

3. DC5V-24V working

4. Support 256MB sd card

5. Lededit software

6. Control led pixel stripe tapes, led amusement lights

1. The programmable T1000s sd card led controller 2048 pixels makes controlling your LED displays easy. Compatible with wide range of addressable LEDs and DMX signal communication protocol.

2. Perfect addressable LED solution for people who don’t want to programme Arduino or other controllers. No programming code required.

3. Using the programmes LEDedit 2016 or Glediator lets you draw your LED patterns visually, you can specify how the LEDs are arranged, preview them, then upload to an SD card. The SD card plugs into the controller and displays your pattern. You can even upload video for your LEDs to display!

Comes with a 256MB SD card included.

Note: To copy files to SD card, you must first format to the SD card. SD card must be formatted as “FAT” format.

Compatible with wide range of addressable LED chipsets:

TM1803/TM1804/TM1809/TM1812/TM1825/TM1826/TM1829/TA9909/TA9912

UCS1903/UCS1912/UCS2903/UCS2909/UCS2912/UCS3903/UCS3912/UCS8903/UCS8904

LPD6803/LPD1886/LPD1882/LPD1889/LPD6812/LPD6813/LPD8806/LPD8809

SM16716/SM16726/SM16711/SM16703

WS2811/WS2801/WS2803/WS2812B/WS2813/ws2815/ws2818

LX1003/LX2003/LX2006

INK1003/INK1009

P9813/P9816/D705/P9823

SK6812/SK6822/SK6812mini/SK9822

APA102/APA102C/APA104/APA2020

TLS3001/TLS3008/TLS3100

Color
RGB
Protocol
SPI
Read More
Pixel LED Multi-function Digital Slave Controller

Pixel LED Multi-function Digital Slave Controller

Leave review

1. Multi-function Digital LED slave Controller

2. With 4 output ports, each port load 512 pixels,2048 pixels maximum

3. Support DMX512 protocol + SPI /TTL protocl IC chips

4. Connect main-controllers to work together

5. On-line is work with Madrix software

6. Off-line controller, program saved in SD card, 15 files maximum

7. Widely used in all DMX512 led products projects

8. There are 8 ports LED slave controller to choose

1. Multi-function Digital Controller. Two control model: Control online mainly means DMX512; Control offline mainly means normal SPI/TTL IC chips.

2. IP address settings on the main controller;

3. Controller with 2G SD card, program saved in SD card for offline playback;

4. Using Fast Ethernet, TCP / IP communication protocol, host connectivity LED controller via standard network cable;

5. Each slave controller has four output ports, a single port output control 512 pixels;

Color
RGBRGBW
Protocol
SPIDMX512
Read More